|
|
PRINT
DATA SHEET |
|
|
PREVIOUS PAGE |
|
|
Fastcom®:
ESCC-104-ET
|
Dual Port
Extended Temperature
Synchronous Communications
RS422/485 Interface Adapter
|
$425.00
|
| |
|
 |
The Fastcom: ESCC-104-ET adapter
is one of the most advanced synchronous communications adapters
in the industry. The Fastcom: ESCC-104-ET supports data
rates up to 10 Mbits/s¹.
The Fastcom: ESCC-104-ET is a dual channel adapter, with
each channel individually configurable to use HDLC/SDLC,
ASYNC, or BISYNC protocols. Although similar to the HSCX,
the ESCC-104-ET expands on the HSCX giving options for:
- CRC generation either CRC-32 or CRC-CCITT polynomials
(CRC-16/CCITT for BISYNC)
- CRC reset state all 1's or all 0's
- Manchester line encoding
- FM encoding (Bi-Phase Space/Bi-Phase Mark)
- Preamble transmission (with repetition)
- BISYNC operating mode, receiving and sending
BISYNC formatted data
- ASYNC operating mode, receiving and sending
ASYNC formatted data, in true asynchronous (no clocks,
data over sampled) or isosynchronous(async data format
with no over sampling)
- True 16 bit data path to FIFO's decrease bus
overhead and timing requirements for higher baud rates
- Both 8 and 16 bit DMA channel selections for
high throughput high megabaud communications
- Interrupt only operation where system resources
are scarce, and very high speeds are not necessary
- Software drivers are included for Windows 2000,
XP, and Linux kernels 2.4 and 2.6
The Fastcom: ESCC-104-ET adapter is designed for
industrial applications requiring rugged construction, high
reliability and full industrial temperature tolerance (-40
C to +85 C). The FASTCOM: ESCC-104-ET is also available
in commercial temperature, model FASTCOM: ESCC-104.
We recommended that you use our Fastcom: LT1 PC/104 Bus termination adapter with our Fastcom: ESCC-104-ET adapter to improve your system's reliability. |
| SPECIFICATIONS: |
- COMM. CONTROLLER:
- DRIVERS/RECEIVERS: RS422 / RS485
- CONNECTOR CONFIGURATION:
- 2x20 Right Angle Latch-Lock Header
- BUS INTERFACE: PC/104
|
| POWER REQUIREMENTS: |
|
| ENVIRONMENT: |
- Storage Temperature Range: -55 to +100 C
- Industrial Operating Temperature Range: -40 to +85 C
- Humidity: 0 to 90% (non-condensing)
|
| FEATURES: |
- High speed, up to 10 Mbits/s¹
- User programmable on-board clock generator
- Dynamic data rates
- Drivers: RS422 / RS485 multi-drop
- Support Full-Duplex and Half-Duplex modes
- Excellent line noise immunity
- Cable lengths up to 4000 feet
- Easier to program and use than other HDLC adapters
- RS485 MODE:
- 32 Fastcom: ESCC-104-ET adapters can share the
same "twisted pair"
- Driver control is automatic
- SERIAL INTERFACE:
- Two independent full duplex serial channels
- On chip clock generation or external clock source
- On chip DPLL for clock recovery of each channel
- Two independent baud rate generators
- Independent time-slot assignment for each channel
with programmable time-slot length
- Async, sync character oriented (MONOSYNC/BISYNC)
or HDLC/SDLC modes (including SDLC LOOP)
- Transparent receive/transmit of data bytes without
framing
- NRZ, NRZI, FM and Manchester encoding
- Modem control lines (RTS, CTS, DTR, DCD, DSR)
- CRC support:
- HDLC/SDLC: CRC-CCITT or CRC-32
- BISYNC: CRC-16 or CRC-CCITT
- Statistical multiplexing
- Continuous transmission of 1 to 32 bytes possible
- Programmable preamble (8 bit) with selectable repetition
rate (HDLC/SDLC and BISYNC)
- Collision resolution
- Programmable bit inversion
- Protocol Support: (HDLC/SDLC)
- Various types of protocol support depending
on operating mode
- Automatic (automatic handling of S- and I-frames;
not auto configure)
- Non-auto mode (manual)
- Transparent mode
- Handling of bit-oriented functions
- Support of LAPB/LAPD/SDLC/HDLC protocol in auto
mode
- Programmable time-out and retry conditions
- Programmable maximum packet size checking
- Modulo 8 and 128 operation
- Storage of up to 17 short received frames
- MP interface and Ports
- 64 byte FIFO's per channel and direction
- 8/16 bit microprocessor bus interface
- All registers directly accessible
- Documentation and software drivers included
- Designed and manufactured by COMMTECH, INC.
Wichita, Kansas, USA
- For a more complete and detailed list of features available
on this card, please see the documentation for the Siemens
ESCC2 SAF82532.
|
¹While
the Fastcom: ESCC-104-ET will operate on any clock rate
from 1 to 10 MHz, It is still plugged into the ISA bus which
will limit overall throughput to a aggregate total of 16
Mbps. What this translates to is that the board will clock
data in or out at 10 Mbps but due to bus limitations it
cannot run full duplex with continuous data at the maximum
clock rate. It can however run non continuously at the maximum
clock rate (either half duplex or forced idle time), or
continuously at a slower clock rate (1-4Mbps 2 channels
full duplex). |
|
|
|
